Monday, July 27, 2009

What Is The Best Softair ?

Installation luggage on a bike with disc brakes.

Engineers - Designers bike, developing a new model of bike, guided by a categories of consumers. Unfortunately, about a category as Cyclists are often overlooked. Some argue that for cycling, there are touring bikes and hybrids. But touring bike, is in essence, a kind of highway that is intended primarily for good roads (but good road Cyclists dislike, because they are a lot of cars) to purchase the same hybrid in the contemporary Russian situation is not quite easy (although the situation is gradually changing for the better).

most common type of bicycle is now a mountain, mountain biking. As a result, many Cyclists use in campaigns bikes of this type. Their versatility, low weight, high permeability, high ground clearance and good handling on bad roads provide high popularity of mountain biking.

And for cyclists is one of the most important pieces of a bicycle - trunk. It is clear that on a bike - dvuhpodves trunk do not deliver, so cycling is used mainly Hard Tail. But often, designers Hard Tail medium upper price categories and for some reason assume that their product will be used only by competition and forget about the trunk.

Установка багажника на велосипед с дисковыми тормозами.

When installing luggage on a bike with disc brakes often stalkivavatsya with the problem - the luggage rack is in contradiction with caliper brakes. Then is the frame has holes for fastening the boot, carving them sliced, but when you try to install the boot of his stand must go through the caliper. Byvat and worse - the frame does not provide any sort of holes for the trunk. Drilling new holes in the same frame is not recommended, it leads to loss of warranty.

As a result, we often hear that the bike with disc brakes can not be used in cycling. Advised to withdraw from the situation by applying cantilever rack, fastened to the seat tube, or carry the whole load in the rucksack (podramnoy bag). But none of these methods can not be called suitable for multi-day hike.

Attention! It happens that to secure the trunk to the frame is missing some fraction of a millimeter. In no case do not try to modify a file caliper disc brakes - the wall of the working cylinder may be surprisingly thin, and a product with rather big price irredeemably flawed! Desirable also to counter the trunk touched any parts brake system.

turns out, the trunk on the bike with disc brakes supply still can. And even in several ways.


first method - applicable if the frame has holes for the trunk. The idea is simple - move the trunk back to its stand did not touch the caliper, and that before he could get at service brakes (brake pads all still need to be changed and brake fluid - too).

This will require the holder to manufacture something like this form.

I made it out of steel corner. Cut down too much, leaving only the rib. This required Bulgarian and metalwork skills. And installed it on the bike. Mounting happened rigid, and the trunk is not walking from side to side.

Установка багажника на велосипед с дисковыми тормозами.

The result - a completely satisfactory. The design is operated during the year stood 25 kg backpack in a ten Bicycle Tours (1 KS), and a large number of one - two - trehnevnyh hikes of the day. Complaints yet.

not excluded, of course, that on a different model bike and trunk shape bracket would have to change. In general, show ingenuity.

Установка багажника на велосипед с дисковыми тормозами.


second method will be used If no holes for the trunk in the frame no. (And what looked when buying a bicycle?)

If the frame is no holes for the trunk, you'll need to use clamps. The trunk is attached to the collar, around the feathers back forks and seat tube. To clamp should be used sheet thickness 1-1.5 mm. To avoid scratches frame, a clamp is put a rubber strip, cut from inner tube.

Mounting got tough enough, though not as both brackets.

holder of this type also successfully withstood several multi-day hikes, no complaints on them there.


Taken here .


Wednesday, July 22, 2009

What Does European Wax Look Like

Customize front derailleur gear.

Adjusting front derailleur is possible only after a fully configured rear.
Before adjustment does not hurt to check state of the tether. If the cable is frayed or Untwist it is better to replace it. And if it is dirty, then it must be cleaned and lubricated. Not greased rope can cause fuzzy gearshift.

preparation.
set the chain on the smallest sprocket at the front and the largest rear. Is in its switch adjusting screw H (High) and L (Low). Weaken the screw cable.
on the control stick to rotate the drum cable tension adjustment clockwise until it stops (if is).



small adjustment programs.

turning the screw, L (Low), set the scope of such provision to the chain is as close as possible to the internal plate, but that when pedaling the chain will not hit the scope.
Then We stretch rope and wrap the cable fixing screw.




Adjustment large transfers

translate the chain on the largest front and smallest rear sprocket rotating screw H (High), establish a position frame to the chain is as close as possible to the outside of the plate, but that when pedaling the chain will not hit the scope.



Check switch operation. This is best done under load, that is just to ride a bike. The chain should move from one sprocket to another smoothly and quickly, and thus should not affect the scope of the switch. If hurt, you have to check the parallelism of the frame and sprocket (maybe switch installed correctly), and the state own star system (perhaps they are deformed).

Saturday, July 11, 2009

Ringworms And African American Hair

Customize cycling disc brakes.

extensive article on how to configure disk brakes.
Customize hydraulics .

The most "entertaining" tune brake mount on the international standard (Hope Mono M4, Hope Mono 6ti, Magura Loise, Gustav ...).
настройка дисковых тормозов
necessary after securing the wheel, center the caliper relative to the rotor, selecting and installing powered supports between the frame and puck caliper from a kit, which have various different thicknesses. Snag that the stronger the delay, the better the interposition of washers and => calipers will be closer to the frame, so by selecting the thickness and number of washers up to a fraction of a millimeter, it is necessary to try many combinations, can only advise, be patient when using the method of trial and errors.

But most manufacturers installation is simple - after installation of the rotor on the hub and wheel in place tighten the bolts (cam) axis. Firmly fasten the adapter (use thread lock welcome).
fasten calipers (typewriter), but the hexagons are not delaying (Calipers should "float"). Hold the brake lever, Checks whether the pads are put forward by pressing the knob.

After clamping of the rotor blocks, calipers must stand in place, but it is better to help him, tugging (trying to twist) the wheel back and forth.

When the calipers get up at the place, gradually, alternately then the upper then the lower bolt, tighten the caliper mount, if the bolts were too loose, the handle can be gradually released, and again tighten abruptly.

Caliper brake pads energized to bring the rotor to the working distance, it is done this way: dramatically (almost blows) to press the brake lever 20-30 times.
releasing the handle, turn the wheel ... If the rotor rubs, look to the light to which block it touches, relaxes the caliper mount and slightly shift it towards the rubbing pad, with the plane of the shoe should be parallel to the plane of the rotor. Tightens slightly attachment, check on clearance, if necessary, repeat the procedure.

If the rotor rubs on both pads can be diluted by removing some adjustment Allen a brake lever while the brake will grab later if you need a smaller move handles on the contrary, the shestigrannichek be screwed, you may need align the rotor.

Once everything is set up, once again stand with all screws and check the work: When you click on the handle shaft should not move and warp.

Customize mechanics
After installing the rotor on the hub and wheel in place, tighten the bolts (cam) shaft. Since the mechanics more sensitive to a shift in the axis of the wheel, I recommend tightening the eccentric directly sitting on the bike or bicycle fork pressed to post dropchika not appear sound of friction on the rotor block. Firmly fasten the adapter (use thread lock welcome), bolted to it calipers (typewriter), but does not pull hexagons (calipers should "float"). Fixed block brings to the half turn screw that adjusts its position.
! In Haes before twisting the adjustment screw, you must unscrew the locking hexagon, and after adjustment of the brake screw it back. !
настройка дисковых тормозов
lightly presses his finger on the part of the fixed calipers (inside blocks), so that the plane of the inner pad exactly coincided with the plane of the rotor.

настройка дисковых тормозов
gently turns fasten the caliper mounting bolts.
plane pads should not be displaced with respect to rotor plane! The operations described in this paragraph, it is better to completely disconnected from the jacket and the cable.
tighten both hex, stocked turns away half turn the adjusting screw, turn the wheel and check the relative position of the rotor and pads up to the light or the sound.

настройка дисковых тормозов
настройка дисковых тормозов
If the rotor does not t then we can move up a little shoe reg.boltom and
Conversely, if the third to push through these checks, the adjustment choose the position of the bolt static pad near the rotor, but without the scratching of the rotor.

We turn the lever (to which the cable is screwed), thereby pressing the movable block, and the rotor should be slightly shifted to a static block, but in any case is not twisted, as shown in the figure (let exaggerated, but it is clear).

настройка дисковых тормозов
Set up a shirt and a rope for a seat in the lever so that the outer pad was pressed, and lightly draw in bolt, gently press the handle to the moment in which the brake should start to grasp, so the cable can slip in mounting arm, and you will have less trouble with the regulations.

delaying fixing the cable, rotate the wheel, if the shoe rubs have a little adjustment screw on the handle, or vice versa unscrew with too much progress.
recommend to adjust the brake so that the adjustment on the handle was minimal vykruchena better perezakrepit cable a lever caliper, it will save the thread handle from damage.

If the desired course handles do not adjust, due to the fact that the rotor is constantly rubs, or rather strike sharply, then he bent and have to dub.

way of Abida and Tektro a useful feature called the preload adjustment recoil. With well-groomed shirts and ropes, easing tightness (twisting hexahedron) can get a sense close to a cheap brake hydraulics, or vice versa, when tightening the filthy or not so well-padded jackets, thereby make the handle back to its original position.

настройка дисковых тормозов
настройка дисковых тормозов
Removal related Troubleshooting
dub rotor:
look at the clearance (better put a white sheet), the edge of the rotor on the pads, turn down an adjustable key in the opposite direction.
настройка дисковых тормозов
Important!
key must be absolutely clean - better than fresh fat!
need to turn down little by little rotor itself and not just twist the brake surface, checking each time to result in transmission, because the excessive force will only make things worse is easily bendable rotor!

need to accurately determine the sector, which is bent in one direction!
with the mechanics of the simpler way: being in a quiet environment, allot a full one of the pads and fairly accurately determine the sector of the rotor angled toward the pressed blocks, which smooths the key, too, we repeat the other shoe, then allot and this leads to the rotor another block and leveled again.

sectors bent over 25 degrees you can dub your hands, but they must be perfectly clean, without the sweat and the more fat.

настройка дисковых тормозов
If the pistons are put forward is not uniform:
mean lateral surface one of them (the one that "inhibits") is blocked.
necessary to remove the wheel, remove the pads. Tight, clean plate with holes for mounting pins pads take no clogged piston and hold it in the retracted position, push the brake lever until lightly pops up contaminated piston lateral surface of which must be wiped clean, then drop it with mineral oil ( non-aggressive to rubber ).

Insert the two piston and wipe any excess oil with a cloth dampened with better gasoline or degreaser.
If the Pistons do not return back:
may have to do the above operation with both pistons, or clogged brake lever, which will have to disassemble and clean, well should check whether or drip from the hose from mastertsilindra actually causes treatable by replacing a line or rubber-porshenkov mastertsilindra.

If the pen has to fall is a clear sign of the presence of air bubbles in the hose or leaking, pumping treated first, second substitution lines and pumping.

If the brakes have lost power is not clear why:
1. check whether there are any pads;
2. completely degrease the pads and rotor, with a solvent, gasoline, alcohol or spices. means, if not rescued, would have ignited pads (Note: they must be metal).
To do this, take them out of the caliper, pulling spring.

настройка дисковых тормозов
slides in a static block, or divorce pad assembly, and shifting to the center in turn take out the two blocks through the slot under the disc.

make burning hot electric stove or a pan on the gas, and suspended both pads close to the heated surface of the steel wire fry in this position for 10-15 minutes until the smoke from them will not leave (if any oil or other dirt). Turn off the tile (gas) and give the pads quietly to cool (do not throw into the water, otherwise would have to grind in the brake).

wipe just in case one more time rotor and pads (they need quickly and completely dry "wet not dry" spot - is nevyzharennoe oil).
Put all the places and set up.

Alekseev Zakharenko (aka Lexapskov).
http://lexapskov.my1.ru/publ/1-1-0-2

Thursday, July 9, 2009

Australian Shepherd Poodle Mix And Allergies

How to straighten eight, an egg on a bicycle wheel.

bicycle wheel at perceives during the movement of heavy loads in all directions - both in vertical (weight cycling) and axial (maneuvers, turns, bumps), as well as in the transverse (accelerations and decelerations). And the magnitude of effort perceived by the wheel, many times greater than the weight of the wheel.

Therefore, even if you ride very carefully on the rim will still be formed defects - that is, violations of its geometric shape. Of course, if the wheel is assembled correctly and with quality parts, these defects would be small, and will have to remove no more than once or twice a year (usually early in the season, and after a serious fall). Inferior rim will require more attention - Eight to them can be formed after each riding on a dirt track.





rim without defects is a circle, completely flat. It should be located exactly in the middle of feathers relative to the fork (rather than relative to flange sleeves!).





on the rim can be formed defects in three types:







«Eight" - when the rim is no longer flat, or when part of the rim does not coincide with the plane of rotation. Most often, already collected on the wheels are formed exactly "eight".









«Egg" - when the rim is no longer a circle, then there is some part of it is closer to the center than others.

«Egg" Eight is rarer, usually after unsuccessful landings.





«Umbrella" - when the rim is not set exactly halfway between the feathers of a fork. Defect of this type is usually the result of improper assembly of the wheel.




Elimination of defects of the rim.

want to learn how to correct defects in the rim itself, should be aware that editing the wheel - an operation which requires not only skill, how much patience and perseverance. Because it's nothing complicated in this case, in essence, no. Assemble the wheel fully considerably complicated, and to accomplish this task the novice cyclist to better address the workshop.

What do I need to learn how to change a wheel?

  1. ready to assemble the wheel. Should not begin to practice on an old, murdered a wheel with multiple defects. Although its the one hand, not sorry. But on the other hand, is not always possible to straighten a wheel to an ideal condition. In addition, to eliminate one small eight simpler than many overlapping figure eights and eggs, especially for a beginner velomehanika. Better start learning a new or nearly new rim, until he got dozens of eights.
  2. piece of chalk to mark the defective area.

  3. Spoke key.

  4. certain amount of free time.

  5. Stanochek Dressing wheels use a very convenient, but not necessarily. Small Group of Eight on the wheel can be removed without removing it from the bike, it is enough to turn over bike upside down. In this case, the correctness of the wheel can be controlled with respect to brake pads and pens of the fork.

Solving "Eight"

For eliminating eight first need to find a place on the rim of the defect. To do this, unwinding and slowly reaching the rim at the side of a piece of chalk. Note chalk, where the rim is deformed, (chalk in this place begins to touch the rim). Thus we determine in what place there is a figure-eight, and in what direction deformed rim.

To address the Group of Eight should tighten spokes on one side of the rim and loosen the tension on the other side. And to do it have consistently - otherwise you may receive the rim of the other defect - "egg".



«Eight" small defect sites was between two adjacent spokes.

Lifts one spoke, for example, 1 / 3 turns, but also weaken the adjacent 1 / 3 of turnover.






«Eight" a small, defective seat was in front of some spokes.

Lifts this needle, for example, 1 / 4 turn, and the two adjacent relax on the 1 / 8 turn.





«Eight" has affected several neighboring spokes.

Spokes, which are closer to the center of the defect, pulls or cuts are stronger than those that are on the edges.




Then again unwinding and see what has changed. If eight was more than she was, then returns all the nipples spokes to its original position, and once disassembled, in what direction they need to twist. If declined, but not until the end - it means that we on the right track, but you must twist the nipple in the same direction.

Removal "eggs"

to eliminate the eggs too, at first need to find a place on the rim of the defect. For this unwinding (with the cover hubcap) and slowly reaching the rim of a piece of chalk (not the side, and outside). Note chalk, where the rim is deformed, (chalk in this place begins to touch the rim). Thus we determine in what place there is a protruding portion of the "egg".


To eliminate the "egg" should tighten the spokes on both sides of the rim.

And this should be done in concert - or the rim of the can receive the "eight".

If tightens a spoke on the half turn the key, then the two neighbors have to tighten a quarter turn.



typically begin this process must be repeated several times before the "eight" or "egg" will disappear. Then, at least the appearance of experience, small defects will disappear with the first - the second attempt.

In addressing eights is important to remember two features:

  • First, the spokes can not pull (You can damage the rim or the nipple). If in the process of editing one or more of the spokes were to pull, we should weaken them, together with the adjacent spokes, and repeat adjustment.

  • Secondly, the spokes should not be relaxed (or they will break down while driving). If in the process of editing one or more of the spokes were loose, should bring them together with the adjacent spokes, and then repeat the adjustment.

Gretchen's White And Blue Bathing Suit

wash the bike.

Tips for washing the bike.

Before I proceed to wash, You can apply a defatting agent for the chain. Should avoid direct contact with water jets to all parts of the bike and especially electronics. Avoid moisture by fixing podflyazhnika to prevent water from entering the frame.

to wash himself, you can use soap (liquid detergent tool, car shampoo) and water, there is truth and special cleansers for bicycles.

In order to clean up the frame, you can use sponge, but more dirty bike parts often need a brush, especially if you want really good to wash a bike.

brush chains and gears, rim and hub. If you use a fork with a protective corrugations, then after washing should compress them to the remaining moisture is drained out.

When washing a bicycle not recommended to use a hose with water under high pressure (albeit of a special cleaning with high pressure bike is just pure a few minutes) because of different mechanisms bicycle bearings do not possess push the water, which fell into the latter under pressure.

You can use a hose with water, but under low pressure and direct water jet directly on the sleeve, the carriage, the gearbox and steering column.

During the bike wash or expose it to direct sunlight, as hot weather and sun dried "frame, contributing to the emergence of on its surface cracks.

After washing, do not leave the bike wet. Wipe the bike clean and dry cloth, then lubricate the chain required.

Making neat appearance and shine the bike will help further processing automotive polishing liquid.

If you keep a bike from the net state - it will serve you longer and better.

Tuesday, July 7, 2009

Steep Analysis For A Salon

How to wash a bicycle chain.

instructions on washing bicycle chain, without special tools.

IMPORTANT! The chain should be removed, In other words there must be a castle, or squeeze you. If you have a cheap chain semirekovaya Semerikova or not, but Mark KMZ - put a lock KMZ. If you have a chain of 8 or 9 - put the SRAM is not afraid, even if you have a chain Shimano.
We ponadyabyatsya:

1. The solvent was 646 (or 647, 650 - any)
2. Plastic bottle (half liter)
3. Laundry powder (any)
Algorithm:)

1.Snimaem chain and throw it into the bottle
2.Zalivaem (about 50 grams) of solvent
3.Boltaem bottle about 5 minutes
4.Slivaem rastvorietel. (Can be reused because it is used not for cleaning, and to soften the dirt and he would stand until it settles all the rubbish and he is again becoming prozraznym).
5.Zalivaem 300 milliliters of well-warm (degrees 70) Water
6.Kidaem a half teaspoons of laundry detergent bottle
7.Boltaem 5 minutes
8.Slivaem water
9. Repeat steps 5,6,7,8 needed (who want)
10. In the bath (circumcision plastic bottle) with water + powder brush to paint wash First one side of the circuit (not side), then another - who would like to. Although I never do.
11.Slivaem dirty water from a bottle and wash the chain with water (you can right in the same bottle)
12.Razrezaem bottle - extract crystal clear chain
13.Sushim it on the battery or a hair dryer or hot kamforke electric cookers (but not red-hot) or in another warm place (to expel the water to prevent rust)
14.Stavim in place a chain and ... lubricates, skating, sticky and all over again ...
15. I More wipe outside the chain oiled cloth (in oil for sewing machines) - solely to prevent corrosion.

Fried Salmon Patties No Egg

Service Contact cycling Pedals Shimano.

Time: 15 minutes
Tools for the job:
- Rag
- plastic cap from the handle
- head on a 9 mm
- The head of 11 mm
- Spanner wrench 15 mm or 6 mm hex
- Grease Motorex Bike Grease 2000
- A small flat screwdriver

Price:
- Approximately $ 10 for lithium grease for the bearings (enough for a lot of the bulkhead)

1. Most contact the pedals are held on the nut with a lock nut, located under a plastic cover. It can get, podsunuv under her head screwdriver or knife blade.

контактные педали Shimano
2. uses 9-millimeter head to loosen the lock nut, and 15-mm key hold the axle so that it does not rotate. After removing the cone of 11-millimeter head and try not to lose the bearings. If the head does not fit in the pedal, try to keep the cone with a screwdriver and rotate the axle on the other side. Some Pedal Type Shimano PDM959 (XTR) dealt with the side of the axis. For their dismantling will only need a pipe wrench, which need to unscrew the plastic nut between the body and axis.

контактные педали Shimano
3. Carefully remove the axle from the housing pedal. Try nothing to lose. Extract all the balls remaining in the body, and remove from the axis of anther, remembering, as he stood. Then remove the remains of grease from the axle and the body.

контактные педали Shimano
4. Apply axle and bearing cups lithium grease, and then expand in places balls. Do not confuse the number! And do not forget to pre-cleaned.

контактные педали Shimano
5. Install the new duster and carefully paste the axle housing.

контактные педали Shimano
6. Stick axis in the sequence, reverse disassembly. Adjust the tightness of the cone so that the pedal rotates easily and smoothly, but without a backlash. Tighten the pedal back to the connecting rod and go skate ...

контактные педали Shimano
Tips mechanics:

When the ball lay on the bearing cup, use the plastic cap of a ballpoint pen. It's much more convenient screwdriver or any other iron, and accordingly Magnetizable and tools.

Material published in the Mountain Bike # 16 (sentyabr'06)!
контактные педали Shimano

How To Build Wakeboard Kicker

Install hydraulic disc brakes.

Installation hydraulic disc brakes on a bicycle.


Hours: half hour

Cost: Will spend about $ 100 to clamp and lock the thread (and, of course, here priplyusuet value of disc brakes, if you have not yet bought)

Tools: cutters hose, clamps, Allen 5 mm, lock the thread (like Loctite)

Tips mechanics:

-Before you start to hang on the frame of other equipment Turn to seal the rear hydraulic line. Remember: like twigs fall into any of the loop. At dvuhpodvesnoy frame check with full compression the rear suspension, not to was sticking out of bends.
-If you're not sure what to put the brakes as necessary (their proper installation is required for your own safety), then head for the nearest Bikes. Hopefully, a few strokes of the wrench with you there are not prompted for an exorbitant price. When will put the brakes, look sharp and remember, the next time you are able to do everything himself.

a . Remove the old brake and clean them. Useful in the economy: it is useful to always have on hand a spare Set the brakes just in case if you have any problems with the hydraulic disc that you can not resolve until the next trip.

2. Put on the wheel brake lever, check to see whether confused right from the left. If the new brake lever, as compared with the covers, longer or shorter, then you have to adjust the mounting knob on the steering wheel so that the stylus arm rose in the right place. In this case, you may have to move the control stick switches a few millimeters inside.


3 . If it becomes necessary to use an adapter for the caliper (it requires many forks with mounting Standard post-mount, such as Manitou and Marzocchi), it means that it was the turn for the installation. Bolts on most cards come with already applied thread lock (this is determined by the way they are plastered with red or blue sticky substance). If they do not lock the thread, do not forget his cause: unlikely you in the middle of the descent like rattle loose bolts.


4. Now set the calipers to the frame / fork. On some models, adapter, or on the body of the caliper instead of round holes for the bolts used extended along the slit. This allows you to make an exact fit. Other manufacturers, such as Hope, offer You tinker with washers and spacers, which are supplied in different sizes. Do not hurry, do the procedure carefully, because rubbing wheels is not so much slow down your movement, how many would get their creaking and you and those who will go near you.


5. Put disc brakes on the hub and secured using the screws - it does not take much time. Just check that bolts do not remove and they were locking the thread. If the bolts for the rotors equipped with exotic heads, it is better to change them on a hexagon bolts - then there will be problems with the tool, and check them for tightness easier. If you have a brake Shimano, it's likely they have a system fastener Center Lock: drive is put on the guide pins and tighten the nuts in the same way as the rear cassette, - Puller tape.


6. With clamps Attach hose to the frame. Some frames come with a hydraulic line guides - specific projections with small holes for the clamp to pinch the hose in it. On the other tabs are used as hooks where to twist the hose to put it in place. Be more careful with it: it is easy to twist the hose (unless it is reinforced with metal, an upgrade is very significant). But before fasten the hose, first Experiment with the options of laying to find the most elegant way of steering the wheels.


material published in Mountain Bike # 8 (noyabr'05)

Friday, July 3, 2009

How To Find A Blueprint Online

Cool video on repair and maintenance velosieda (English)

Tay Sachs Important Facts

Processing bicycle frame.