Thursday, July 9, 2009

Australian Shepherd Poodle Mix And Allergies

How to straighten eight, an egg on a bicycle wheel.

bicycle wheel at perceives during the movement of heavy loads in all directions - both in vertical (weight cycling) and axial (maneuvers, turns, bumps), as well as in the transverse (accelerations and decelerations). And the magnitude of effort perceived by the wheel, many times greater than the weight of the wheel.

Therefore, even if you ride very carefully on the rim will still be formed defects - that is, violations of its geometric shape. Of course, if the wheel is assembled correctly and with quality parts, these defects would be small, and will have to remove no more than once or twice a year (usually early in the season, and after a serious fall). Inferior rim will require more attention - Eight to them can be formed after each riding on a dirt track.





rim without defects is a circle, completely flat. It should be located exactly in the middle of feathers relative to the fork (rather than relative to flange sleeves!).





on the rim can be formed defects in three types:







«Eight" - when the rim is no longer flat, or when part of the rim does not coincide with the plane of rotation. Most often, already collected on the wheels are formed exactly "eight".









«Egg" - when the rim is no longer a circle, then there is some part of it is closer to the center than others.

«Egg" Eight is rarer, usually after unsuccessful landings.





«Umbrella" - when the rim is not set exactly halfway between the feathers of a fork. Defect of this type is usually the result of improper assembly of the wheel.




Elimination of defects of the rim.

want to learn how to correct defects in the rim itself, should be aware that editing the wheel - an operation which requires not only skill, how much patience and perseverance. Because it's nothing complicated in this case, in essence, no. Assemble the wheel fully considerably complicated, and to accomplish this task the novice cyclist to better address the workshop.

What do I need to learn how to change a wheel?

  1. ready to assemble the wheel. Should not begin to practice on an old, murdered a wheel with multiple defects. Although its the one hand, not sorry. But on the other hand, is not always possible to straighten a wheel to an ideal condition. In addition, to eliminate one small eight simpler than many overlapping figure eights and eggs, especially for a beginner velomehanika. Better start learning a new or nearly new rim, until he got dozens of eights.
  2. piece of chalk to mark the defective area.

  3. Spoke key.

  4. certain amount of free time.

  5. Stanochek Dressing wheels use a very convenient, but not necessarily. Small Group of Eight on the wheel can be removed without removing it from the bike, it is enough to turn over bike upside down. In this case, the correctness of the wheel can be controlled with respect to brake pads and pens of the fork.

Solving "Eight"

For eliminating eight first need to find a place on the rim of the defect. To do this, unwinding and slowly reaching the rim at the side of a piece of chalk. Note chalk, where the rim is deformed, (chalk in this place begins to touch the rim). Thus we determine in what place there is a figure-eight, and in what direction deformed rim.

To address the Group of Eight should tighten spokes on one side of the rim and loosen the tension on the other side. And to do it have consistently - otherwise you may receive the rim of the other defect - "egg".



«Eight" small defect sites was between two adjacent spokes.

Lifts one spoke, for example, 1 / 3 turns, but also weaken the adjacent 1 / 3 of turnover.






«Eight" a small, defective seat was in front of some spokes.

Lifts this needle, for example, 1 / 4 turn, and the two adjacent relax on the 1 / 8 turn.





«Eight" has affected several neighboring spokes.

Spokes, which are closer to the center of the defect, pulls or cuts are stronger than those that are on the edges.




Then again unwinding and see what has changed. If eight was more than she was, then returns all the nipples spokes to its original position, and once disassembled, in what direction they need to twist. If declined, but not until the end - it means that we on the right track, but you must twist the nipple in the same direction.

Removal "eggs"

to eliminate the eggs too, at first need to find a place on the rim of the defect. For this unwinding (with the cover hubcap) and slowly reaching the rim of a piece of chalk (not the side, and outside). Note chalk, where the rim is deformed, (chalk in this place begins to touch the rim). Thus we determine in what place there is a protruding portion of the "egg".


To eliminate the "egg" should tighten the spokes on both sides of the rim.

And this should be done in concert - or the rim of the can receive the "eight".

If tightens a spoke on the half turn the key, then the two neighbors have to tighten a quarter turn.



typically begin this process must be repeated several times before the "eight" or "egg" will disappear. Then, at least the appearance of experience, small defects will disappear with the first - the second attempt.

In addressing eights is important to remember two features:

  • First, the spokes can not pull (You can damage the rim or the nipple). If in the process of editing one or more of the spokes were to pull, we should weaken them, together with the adjacent spokes, and repeat adjustment.

  • Secondly, the spokes should not be relaxed (or they will break down while driving). If in the process of editing one or more of the spokes were loose, should bring them together with the adjacent spokes, and then repeat the adjustment.

0 comments:

Post a Comment